Solar Controllers
Looking for a new scent? Check out our fragrance
Steca Solarix MPPT
MPPT 1010, MPPT 2010
Steca Solarix MPPT is a solar charge controller with Maximum Power Point Tracking. It is specially designed to work with all established module technologies and is optimized for solar systems with module voltages higher than the battery voltage. The Steca Solarix MPPT is especially qualified in combination with grid tied solar modules. The advanced MPP-tracking algorithm from Steca assures that the maximum available power of the solar generator is charged to the batteries. The Steca Solarix MPPT with latest technology ensures full performance in all conditions, a professional battery care combined with modern design and excellent protection.
* Suitable for small home systems
* Specially suitable for all kinds of telecommunication applications
* Night light function
* 480w Maximum input power of the solar modules
Product features
- Maximum Power Point Tracker (MPP tracker)
- Voltage and current regulation
- PWM control
- Current compensated load disconnection
- Automatic load reconnection
- Temperature compensation
- Monthly maintenance charge
Electronic protection functions
- Overcharge protection
- Deep discharge protection
- Reverse polarity protection of load, module and battery
- Reverse polarity protection by internal fuse
- Automatic electronic fuse
- Short circuit protection
- Overvoltage protection at module input
- Open circuit protection without battery
- Reverse current protection at night
- Overtemperature and overload protection
- Battery overvoltage shutdown
Displays
- Multifunction LED display
- Multi-coloured LED
- 5 LEDs show operating states
- for operation, state of charge, fault messages
Steca Solsum Charge Controller 10.10F Product features
*Suitable for very small homes
*Maximum PV input 240W (2 x 120W modules)
The Steca Solsum F-Line continues the huge success of one of the most used SHS controllers. With a power range of up to 10 A at automatically recognized 12 V or 24 V it fits to a system sizes of maximum 240 W.
- Series controller
- Voltage regulation
- Automatic detection of voltage
- MWM control
- Multistage charging technology
- Current compensated load disconnection
- Automatic load reconnection
- Temperature compensation
- Common positive grounding or negative grounding on one terminal
- Monthly maintenance charge
Electronic protection functions
- Overcharge protection
- Deep discharge protection
- Reverse polarity protection of load, module and battery
- Automatic electronic fuse
- Short circuit protection of load and module
- Overvoltage protection at module input
- Open circuit protection without battery
- Reverse current protection at night
- Overtemperature and overload protection
- Battery overvoltage shutdown
Displays
- Multifunction LED display
- Multi-coloured LED
- 4 LEDs show operating states
- for operation, state of charge, fault messages
Microcare MPPT Solar Charge Controllers are proudly South African. The Microcare MPPT utilizes PWM and integrated technology to provide greater than 96% efficiency from your solar panels. The actual charge current increase you will see varies primarily with module temperature and battery voltage. In comfortable temperatures, current increase typically varies between 10 to 25%, with 30% or more easily achieved with a discharged battery and cooler temperatures.
What you can be sure of is that the Microcare MPPT charge controller will deliver the highest charge current possible for a given set of operating conditions. The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster.
Features:
* Automatic selection of Battery voltage (12v-48v)
* Input panel voltage (20voc-150voc)
* Circuit Breaker protection – Full input and output protection
* Electronic current limiting.
* 4 Line LCD Display
* Battery Voltage
* Charge Mode (Equalize, Boost and Float.)
* Charge Current
* Panel Voltage
* Output Power from Panels
* State of charge
* Data Logger
* 24hr Average
* 60 day logger
* Programmable features
* Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
* Peak greater than 96% efficiency
40 Amp LCD Microcare MPPT Solar Charge Controller for sale South Africa
Microcare MPPT Solar Charge Controllers are proudly South African. The Microcare MPPT utilizes PWM and integrated technology to provide greater than 96% efficiency from your solar panels. The actual charge current increase you will see varies primarily with module temperature and battery voltage. In comfortable temperatures, current increase typically varies between 10 to 25%, with 30% or more easily achieved with a discharged battery and cooler temperatures.
What you can be sure of is that the Microcare MPPT charge controller will deliver the highest charge current possible for a given set of operating conditions. The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster.
Features:
* Automatic selection of Battery voltage (12v-48v)
* Input panel voltage (20voc-150voc)
* Circuit Breaker protection – Full input and output protection
* Electronic current limiting.
* 4 Line LCD Display
* Battery Voltage
* Charge Mode (Equalize, Boost and Float.)
* Charge Current
* Panel Voltage
* Output Power from Panels
* State of charge
* Data Logger
* 24hr Average
* 60 day logger
* Programmable features
* Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
* Peak greater than 96% efficiency
The MICROCARE MPPT REGULATOR is designed to interface between the SOLAR PANEL, the BATTERIES and the LOAD. The TRACKER will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series pass regulators.
The MICROCARE MPPT REGULATOR is also able to charge batteries of a lower voltage than the solar panel. By means of LEDS it will show the status of the system. It also incorporates various charge modes which will automatically increase the charge level to the batteries when first starting up or if the battery voltage falls below the minimum volts.
The MICROCARE MPPT REGULATOR will read the nominal battery voltage. This unit is designed to run on a 12/24 volt battery set. It will then read the solar panel voltage and automatically find the optimum power point. The charging, battery values and boost modes are then automatically adjusted.
Via links the load voltage disconnect can be selected, whether the battery is lead acid or sealed, and whether the unit operates as a normal load shedder or as a day/night switch.
Features
- Automatically measures the battery voltage and then sets up the charge parameters (12v-24v)
- Operates the Solar Panels at the maximum efficiency
- Charges batteries by setting up the best power point of the solar panels
- Can improve power extracted from the solar panels by 30% over normal shunt/series pass regulators
- LED Display
- Maximum Current 30 Amps.
- 30 amp Load controller.
- Temperature controlled Cooling Fan
- Selectable low voltage disconnect.
- 24 hour load or Street Light mode
Specifications
- Output Current Rating: 30 amps
- Nominal Battery Voltage: Multi-Voltage 12-24vdc (Automatic selection of voltage)
- PV Input Voltage: Absolute Maximum 50VDC
- Charge Algorithm: 2-stage Boost/Float
- Boost Voltage: Charges to 14.8v for minimum of 3 hours (12v system) 29.6v (24v system)
- Float Voltage: 13.8v per battery (12v system) 27.6v (24v system)
- Power Conversion: DC/DC Switch Mode
- Output Efficiency: >95% Typical @ 14 Volt 15 Amps Output
- Voltage Step down Capability: Can charge a lower voltage battery from a higher voltage PV array.
20 Amp LCD Microcare MPPT Solar Charge Controller
Microcare MPPT Solar Charge Controllers are proudly South African. The Microcare MPPT utilizes PWM and integrated technology to provide greater than 96% efficiency from your solar panels. The actual charge current increase you will see varies primarily with module temperature and battery voltage. In comfortable temperatures, current increase typically varies between 10 to 25%, with 30% or more easily achieved with a discharged battery and cooler temperatures.
What you can be sure of is that the Microcare MPPT charge controller will deliver the highest charge current possible for a given set of operating conditions. The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster.
Features:
* Automatic selection of Battery voltage (12v-48v)
* Input panel voltage (20voc-150voc)
* Circuit Breaker protection – Full input and output protection
* Electronic current limiting.
* 4 Line LCD Display
* Battery Voltage
* Charge Mode (Equalize, Boost and Float.)
* Charge Current
* Panel Voltage
* Output Power from Panels
* State of charge
* Data Logger
* 24hr Average
* 60 day logger
* Programmable features
* Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
* Peak greater than 96% efficiency
The MICROCARE MPPT REGULATOR is designed to interface between the solar panel, the batteries and the load. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries.
Using this system up to 30% more power can be extracted from the solar panel than using shunt or series pass regulators. The regulator is also able to charge batteries of a lower voltage than the solar panel. By means of LEDS it will show the status of the system. It also incorporates various charge modes which will automatically increase the charge level to the batteries when first starting up or if the battery voltage falls below the min volts. The regulator will read the nominal battery voltage. This unit is designed to run on a 12/24 volt battery set. It will then read the solar panel voltage and automatically find the optimum power point. The charging , battery values and boost modes are then automatically adjusted.
Via links the load voltage disconnect can be selected, whether the battery is lead acid or sealed, and whether the unit operates as a normal load shedder or as a day/night switch.
Features
JUMPER SELECTION
* Load disconnect. Place the jumper onto the selected low voltage disconnect.
* Remove the battery jumper for Sealed Gel Batteries.
* Remove the jumper if the DAYLIGHT SWITCH is required
CONNECTING THE UNIT.
* Ensure that all cabling used is kept as short as possible as volt drops caused by long cables will reduce the efficiency of the TRACKER. Connect the unit as shown in the diagram. Minimum recommended wire diameter = 4 mm²
* First connect the Load and then the Battery.
* The Led display will show the TRACKER checking the battery voltage. The MEDIUM led will flash once for a 12 volt battery and twice for a 24volt system. At the same time the buzzer will sound once for a 12 volt and twice for a 24 volt system.
* Connect the solar panel. The PANEL led will come on if there is panel power.
* The Regulator will now read the solar panel voltage and select the optimum power point. If there is sufficient power in the solar panel the TRACKER will now start charging.
CHARGING THE BATTERIES.
BOOST MODE: The batteries are charged until they reach the boost voltage 14.8 or 29.6. When the batteries reach this level the tracker will hold this rate for a minimum of 1/2 hour indicated by flashing BOOST LED and then switch to Float Mode. If the batteries fall below the BOOST voltage then the timer is reset ie at night or during cloudy days. This ensures that the batteries are fully Boosted.
FLOAT MODE: Boost Light is off - The batteries are now essentially in trickle charge mode
6 LED DISPLAY
· Panel
· Load
· Boost
· Full Battery
· Medium Battery
· Low Battery
AUDIBLE BUZZER
When the batteries are connected for the first time the buzzer will sound once for 12 volt and twice for a 24 volt battery set. The buzzer will beep when the battery voltage has reached within 1/2 a volt of the battery load disconnect for a 12 volt system and within one volt of load disconnect for a 24 volt battery set. The Buzzer will beep 10 times when the load disconnect is about to trip.
RESET BUTTON.
Pushing the reset button cancels the buzzer. If the unit is in LOAD SHED the reset button will reset the load but if the voltage is too low then the load disconnect will operate.
Technical Specs
MAXIMUM SOLAR PANEL VOLTAGE: 50.0 V DC
MAXIMUM BATTERY SYSTEM: 24 DC<
MAXIMUM CHARGE CURRENT: 10A DC
MAXIMUM LOAD: 10 AMPS
FLOAT CHARGE VOLTAGE: 13.8v 27.6 volts DC
BOOST CHARGE VOLTAGE: 14.8v 29.6 volts DC
MAXIMUM PANEL SIZE: 12 volts - 120 watts; 24 volts - 240 watts
The Microcare Maximum Power Point Tracker Regulator is designed to interface between the solar panel, the batteries and the load. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series PWM regulators. The Microcare MPPT Regulator is also able to charge batteries of a lower voltage than the solar panel. By means of LED it will show the status of the system. It also incorporates various charge modes which will automatically increase the charge level to the batteries when first starting up or if the battery voltage falls below the minimum volts.
Luminous Solar Retrofit is an upgraded version of Solar charge controller which converts conventional Inverter into hybrid solar system. i.e. if you already have inverter and battery, By adding Suitable Solar Panel and Solar retrofit, your system will be converted into solar solution. It works with Single battery (12V) and Double battery (24V) Inverter system.
Product Descriptions
Model Name | SRS 1220 |
System rating | 20 Amp @ 12 Volt, 24 V |
Charging current (max) | 20 Amp |
Panel Support | Up to 800 Watts |
Power connection | 30 A Terminal block |
Solar panel voltage (max) | 25 V |
Wire Size (max) | 6 square mm |
Features
- Easy to Install and use
- Solar optimization technique
- Three modes selections
- LED/ LCD indications
- Inbuilt reverse polarity & reverse current protection
Technical specifications
- Battery type selection switch
- Four operational modes: auto/manual/charger/100% solar
- Compatible with wide range of PV panel array wattage
- Inbuilt protections for short circuit, over voltage, over current, over charge and deep discharge
Luminous Solar MPPT charge controller is an advanced technology product that tracks the maximum power point of PV array to deliver maximum available current to charge battery for off grid photovotalic (PV) systems. The controller provides the better efficiency and significantly less power loss. The Luminous MPPT battery charging process has been optimized for long battery life and improved system performance. The controller is featured with liquid crystal display(LCD) with backlight, eight adjustable settings switches (DIP switch), several communication ports, temperature compensated charging and in built data logging
Product Descriptions
Maximum battery current | 20 amps |
Nominal system voltage | 12 & 24 V DC |
Peak conversion efficiency | 97% |
Maximum solar open circuit voltage | 48V DC for 12V System and 60 V DC for 24Volt System |
Maximum Solar PV Panel Support | Upto 600 Watts (300 Watts – 12V, 600 Watt- 24V) |
Charging stages | Bulk, Absorption, Float & equalize |
Mounting | Wall Mount |
Battery high voltage charging disconnect | 15.5 V (12V) and 31 V (24V) |
Standby Power consumption | < 10 mA |
Features
- smart Tracking algorithm
- Four stage battery charging - Bulk, Absorption, float and equalize
- Automatic selection of battery voltage
- Higher input voltage from PV module
- easy upgradation
Protections
- Surge Current,
- Battery Overcharging
- Over Temperature
- PV high voltage protection
- Battery High voltage cut off
- Reverse current flow at night
- Battery Reverse polarity
- Solar PV Panel Reverse Polarity
- Battery Open Protection
Led Indications
- Green Led – Indicates PV Status
- Yellow Led – Indicates Battery Charging status
- Red Led – Glows in case of faults
Luminous Solar Retrofit is an upgraded version of Solar charge controller which converts conventional Inverter to solar system. It converts 5 KVA 96 volt (8 battery system) Inverter into Solar Hybrid Inverter.
Product Descriptions
Model Name | Shine 9650 |
System rating | 50 Amp @ 96 Volt |
Charging current (max) | 50 Amp |
Panel Support | Up to 5600 Watts |
Power connection | 60 A Terminal block |
Solar panel voltage (max) | 180 V |
Wire Size (max) | 16 square mm |
Features
- Easy to Install and use
- Solar optimization technique
- Three modes selections
- LED/ LCD indications
- Inbuilt reverse polarity & reverse current protection
- Battery type selection switch
- Four operational modes: auto/manual/charger/100% solar
- Compatible with wide range of PV panel array wattage
- Inbuilt protections for short circuit, over voltage, over current, over charge and deep discharge
- 1